Xilinx ZYNQ7000 XC7Z020 FPGA Development Board Zedboard with FMC LPC two-Gigabit-Ethernet two-HDMI-compatible two-SD Gyroscope

Xilinx ZYNQ7020 FPGA Development Board Zedboard with FMC Dual-Gigabit Ethernet Dual-HDMI-compatible outputs Dual-SD Cards Gyroscope Accelerometer

The main chip parameters are as follows:

• Chip model: XC7Z020-2CLG484I
  

• Processor model: Dual-core Cortex-A9
  

• Processor frequency: 766MHZ
  

• DDR3 (PS): 1GB(1024M), 32 bit wide, 1066M data rate
  

• Logic units (LC): 85K
  

• Lookup table (LUT): 53200
  

• DSP unit multiplier: 220
  

• Trigger: 106400
  

• RAM: 4.9MBit
  

• Speed class: -2
  

• Device grade: Industrial -40 to 85 degrees C
  
  

Development board parameters are as follows:

Power supply: through the special TYPE - C interface for the development board power supply, is 9-12V DC - IN interface.

Development board clock: 33.33M (PS), 50M (PL).

Ethernet: Gigabit RTL8211E, RGMII interface, one PS, one PL.

USB interface: USB2.0, PS terminal TYPE - C interface, support HOST and SLAVE function.

(Note 1: Adaptor can extend HOST, can be connected to HUB)

(Note 2: SLAVE does not support hot-plugging because the interface is designed not to draw power)

Debugger: On-board UART + JTAG programmer, supports ARM and FPGA development.

Power supply: Includes a TYPE-C interface power cable, 9-12V/3-5A input.

SD Card Slot: SD0 of PS, SD0 can be BOOT . SD card supports up to 32G.

SD NAND: SD1 of PS, chip model CSNP1GCR01, 128MByte capacity.

HDMI-Compatible Interface: Two PL HDMI-Mini outputs, support up to 1080P.

User LEDs and pushbuttons: one pin-button for PS, two pin-buttons for PL. Two PS LEDs, four PL LEDs.

Startup setting switch: a B00T dip switch for startup setting .

On-board OLED module: 0.96" 128*64 monochrome 0LED, SPI interface at PL .

Camera Interface: A MIPI CSI 2LANE15PFPC1.0 camera interface.

On-board FLASH: 128Mbit(16M bytes).

Onboard FMC Interface: The FMC LPC is a standard 34 differential + 2 clock pairs. FMC provides ADJ1 voltage, 3.3V, 9/12V power supply.FMC interface is compatible with ZEDBOARD's FMC pin definition.

Expansion IO ports: 34 IO ports, BAN13, providing 5V, 3.3V power supply. Default 3.3V level standard 34 single-ended IOs, all alignments are equal length and consider PIN DELAY.

System Reset: A system reset (POR) button.

Board Indicators: DONE, USBCPEN, PG and Power Plugged In indication.

Board Power System: Input DC to 5V/5A.

On-board kernel power supply: 1.0V/6A.

Remaining circuits: 1.8V/3A, 1.5V/3A, 3.3V/3A.

BANK3435 power supply ADJ1 of FMC: 2.5V/3A by default.

BANK13 power supply ADJ2 of 40P expansion IO port: default 3.3V/3A.

Note 1: All TYPE-C except DC - IN can be powered, the rest of TYPE-C are suspended and have no power supply function.

Note 2: FMC uses BANK3435 as HR BANK, only 2.5V ADJ1 voltage supports LVDS _25 differential standard.

Note 3: 40P uses BANK13 as HR BANK, all are single-ended signals.

The Shipping List:

• 1 X ZYNQ7020 development board